Jwev wanscam
![jwev wanscam jwev wanscam](https://images-na.ssl-images-amazon.com/images/I/41766Zbos6L.jpg)
If the detectors do not show the yellow and red, they are not correctly aligned or there is something in between the detector and the reflector. These detectors are situated on each side of the top cylinder, near the metal box that contains the drive system. Now two leds (little lamps yellow and red) on both photo-electric detectors must be lit. Put the "main switch" into the "on" position (vertical)ģ. Any alterations in the electrical circuit or the program of the inverter should be performed by qualified electricians.Ģ. This machine should be connected to a 220-250 V AC outlet with PE (earth) connection to avoid electrical shock. If you are in doubt about an electrical connection you can find help in the electric wiring scheme's here below.
#Jwev wanscam manual
You can start reading the instructions that are valid for the manual JPV press or instructions that are valid for the manual JW press and just add the electro-mechanical components. However if you are enough qualified for this sort of work, it is possible. The electric and mechanical system makes is even more complicated than the manual versions of these presses. We recommand not to do the assembly/disassembly yourself. It should be fixed in such a way that it is easy to operate in case of an emergency.Īssembly and disassembly of these machines. The mushroom shaped safety stop can either be fixed to the floor or somewhere else. Almost every country uses a different system, so it is wiser to leave this up to the local qualified electricians. It is possible that the power cord (electric cable) is not fitted with the right electric plug.
#Jwev wanscam full
Because of the presence of this space it is always certain the the bed is in full contact with the lower roller, which minimizes slippage. The plastic rollers should alway have a certain play between the bed (Play "B"). With an "Allen key" the screw with inside hexagonal can be untightened which allows the change of position. The position of the round bars with plastic rollers can be changed vertically. These guides can be secured with the hexagon bolts. It is important that all the bed guides are in line and have about the same play. This space should be approximately 1 or 2 mm. The four bed guides can be shifted sideways, which changes the open space between the guide and the bed. It is advisable however to check the four guides, fixed on top of the side frames, that keep the bed plate in place.Īlso the steel bars between the side frames that carry the plastic rollers might be adjusted. The rollers must be clean and dry before use. The rollers must be cleaned from grease with a solvent.
![jwev wanscam jwev wanscam](https://sc01.alicdn.com/kf/HT1qJUNFIFdXXagOFbXd/200605467/HT1qJUNFIFdXXagOFbXd.jpg)
Make a very small cut in the plastic tape which allows you to peal off this material. For safety reasons these rollers are packed with grease paper and plastic tape. The two shafts between the side frames and positioned above the top roller, are strong enough to carry the weight during this process.
![jwev wanscam jwev wanscam](https://www.bazaargadgets.com/image/cache/catalog/products/electronics/security/WanscamJW0009TFCardSupportP2PMotionDetectionSecurityCamera-SKU093948-4-1100x1100.jpg)
The machine should now be lifted to be able to take the pallet out. Take this packing material from the press and take the screws out that fix the machine on the pallet.
![jwev wanscam jwev wanscam](https://img.diytrade.com/smimg/2109443/41831772-1686393-0/WANSCAM_Model_HW0025_720P_1MP_HD_PTZ_Wifi_IP_Camera/af30.jpg)
The press is fixed to a wooden pallet and is packed and rapped in cardboard and plastic foil.
#Jwev wanscam series
User's instructions, Polymetaal etching presses JPVEV series (JPVEV-70, JPVEV-80, JPVEV-90), and JWEV-series (JWEV-80, JWEV-100, JWEV-120) electric etching presses with continuously variable printing speed.